TensorGrip F55 is a 22L / 22Kg fast dry pot of, NON-MECL adhesive. This spray adhesive is suitable for high demanding applications for foam, fabric and upholstery applications.
The unique glue formula in this spray pot blends the benefits of non chlorinated technology with a fast flash off time for ultimate user safety and efficiency.
F55 has been designed with a tough cure glue line, making it perfectly suited to high demand curved bonding applications where fast grab is essential.
Spray adhesive main features
When it comes to this contact adhesive it can be used to bond materials on to the following materials.
- Ultra Fast Dry
- High Temperature resistance – 115 degrees
- Tough bond line
- Non-MECL Formulation
- Fine web spray pattern
- MDF
- Plywood
- Synthetic leather
Spray adhesive consistancy
This consistancy of this contact adhesive is fine web like pattern.
Spray adhesive uses information
When it comes to this contact adhesive it can be used to bond materials on to the following materials.
- Foam
- Fabric
- Upholstery
Coverage information for this spray glue
This contact adhesive can cover an area up to 4M2.
Advantages of using F55
F55 has a number of advantages. Some of these are:
- Fast Drying
- Good Heat Resistance
- Very High Solids
- Non-Chlorinated Adhesive
Save when you buy in bulk
We offer bulk buying options with this sprayable glue. So the more you buy, the more you save.
Technical information
| Property | Value |
|---|---|
| All the information is based on practical experience and is published in good faith. However, because we have no control over the manner or conditions in which our products are used, or over work undertaken or end product manufactured by the purchaser, we cannot accept liability for results.
Responsibility for ascertaining the suitability of products for his purposes rests with the purchaser. All conditions, representations, statements, warranties or guarantees whatsoever, whether express, implied or statutory, in respect of any goods manufactured, sold or supplied by us are hereby expressly excluded and we accept no liability in respect of any claim for damage or consequential loss caused to any property arising directly or indirectly out of the use of our products or goods. |
|
| Total Solids | 28%-30% |
| Colour | Clear or Green |
| System Flammability | Flammable adhesive solution in flammable propellant |
| Shear adhesion failure temperature | > 115C |
| Dry Time | 1-2 mins dependent on temp & humidity |
Contact canister storage and canister change over instructions
To change over the canister turn the valve on the canister into the off position, then spray out any remaining adhesive left in the hose.
Next, disconnect the spray hose and gun from the canister.
Reconnect the spray hose to a canister of cleaning solvent (sold separately) and spray out until liquid is clear – which indicates that the hose and gun are clean.
If you choose to leave the hose and spray gun on the canister, leave the valve on the canister open, and do not disconnect the hose & gun from the canister.
Close and lock the spray gun.
Handling & Storage Information
- Consult Material Safety Data Sheet prior to use
- DO NOT store at temperatures over 50C
- Avoid exposure to direct sunlight
- DO NOT store directly on a concrete floor
- For optimum performance, store at 18C during use; but, it must always be above 10C
- When connected, keep the valve open and hose pressurised at all times
- DO NOT close the valve until ready to connect to new cylinder
- Release pressure in hose before disconnection
- Always test product to determine suitability for your particular application prior to use in production
How to use this contact spray adhesive
This glue is designed to be applied to two surfaces to be bonded together. Consequently, for best results, the temperature of the adhesive and the surfaces being bonded should be between 60F – 80F (16C – 27C).
Use with adequate ventilation, and when possible we recommend shaking the canister well before using.
Attach and secure the hose tightly onto the spray gun with required tip, and attach the other end of the hose onto the canister.
Make sure the hose-valve connections are securely tight, and then open the valve on the canister slowly and fully, checking for leaks during this process. Then once open unlock the trigger on the spray gun to start spraying. It is as simple as that.
Prior to use, please check compatibility by spraying a small test patch of the adhesive on the substrate, and this glue may degrade some substrates.
Spraying recomendations
- Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc…
- Spray about 10-20 cm (4″ – 8″) away at a 90 degree angle to the surface, applying a uniform, even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another coat of this adhesive in areas that appear to need more adhesive.
- Spray both surfaces to be bonded, one surface vertically and the other surface horizontally
- Allow 2 – 3 minutes for the adhesive to tack off until no adhesive transfers to the knuckle when touched.
- Adhere surfaces and press together with adequate pressure.
- roller is recommended to apply a uniform pressure to achieve maximum strength.
- Allow 24 hours for the adhesive to fully cure.
- If the spray tip clogs, unscrew the spray tip from the gun and clean with solvent such as lacquer thinner or acetone. Do not use a pin on the spray tip orifice
Not sure if this spray adhesive is right for you?
If you are not sure if this contact adhesive is right for your individual requirements please do not hesitate to Contact our friendly sales team and we will be happy to help you.
Do you require a Certificate of Conformance and traceability?
If you require a Certificate of Conformance, please contact us after ordering (either by phone or email) and we will get this sent out to you with your order.
Reviews
There are no reviews yet