GEKKO G70 is a 500ml can of fast-drying Acrylic adhesive suitable for bonding domestic cushion flooring. Being plasticizer migration resistant this adhesive is suitable for use on a variety of subfloors
The G70 spray glue is a cost effective, non chlorinated fixing solutions for vinyl flooring materials.
Fast Drying Formula
One of the standout features of the G70 is its fast-drying formula, which allows for rapid assembly and bonding of cushion flooring systems.
Spray adhesive uses information
When it comes to this contact adhesive, it can be used to bond materials onto the following materials.
- Vinyl Flooring
- Cushion Flooring
Coverage information for this spray glue
This contact adhesive can cover an area up to 4M2.
Advantages of this spray adhesive
When it comes to this contact adhesive, it has many advantages. Some of those are:
- Good Value
- Plasticizer Resistant
- High Grab
- Tough Bond
- Easy Application Control
Glue consistency
The consistency of this contact adhesive is web-like.
Technical information
| Property | Value |
|---|---|
| Consumption | 15-20 g/m |
| Colour | Clear |
| System Flammability | Non Flam Adhesive/Flam Propellant |
| Ready for Traffic | Â After 30 minutes |
| Flash Off Time | Â 3-5 minutes |
| Dry time | 1-3 minutes dependant on temperature & humidity |
| Open time | 50 minutes |
Handling & Storage Information
- Consult Material Safety Data Sheet before use
- DO NOT store at temperatures over 50°C
- Avoid exposure to direct sunlight
- For optimum performance, store at 18°C during use; but it must always be above 10C
- Always test the product to determine suitability for your particular application before use in production
How to use this contact spray adhesive
This product is designed to be applied as a single sided adhesive to the following recommended subfloors
Flooring Grade Ply
Hardboard
Chipboard
OSB Board
Laytex Screed
Concrete
Calcium Sulphate-Anhydrite Screeds
Plaster Board
Double sided bonding is possible where a stronger more permanent bond is required. Please ensure any pre-bonding, testing and surface preparation has been completed.
Spraying recommendations
- Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc…
- Spray about 10-20 cm (4″ – 8″) away at a 90° angle to the surface, applying a uniform, even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another coat of this adhesive in areas that appear to need more adhesive.
- Spray both surfaces to be bonded, one surface vertically and the other surface horizontally
- Allow 2 – 3 minutes for the adhesive to tack off until no adhesive transfers to the knuckle when touched.
- Adhere surfaces and press together with adequate pressure.
- roller is recommended to apply a uniform pressure to achieve maximum strength.
- Allow 24 hours for the adhesive to cure fully.
- If the spray tip clogs, unscrew the spray tip from the gun and clean with a solvent such as lacquer thinner or acetone. Do not use a pin on the spray tip orifice
Disclaimer
While all the information is derived from practical experience and shared in good faith, we can’t accept liability for the results. This is due to our need for control over how our products are used or the specific conditions in which they operate.
Responsibility for ascertaining the suitability of products for their purposes rests with the purchaser.
All conditions, representations, statements, warranties or guarantees whatsoever, whether express, implied or statutory, in respect of any goods manufactured, sold or supplied by us are at this moment expressly excluded, and we accept no liability in respect of any claim for damage or consequential loss caused to any property arising directly or indirectly out of the use of our products or goods.
What types of materials can I bond with Gekko G70 spray glue?
The G70 is suitable for bonding vinyl and cushion flooring materials.
How long does it take for the Gekko G70 to dry?
The G70 has a fast-drying formula for rapid assembly and bonding. Depending on the bonded materials and environmental conditions, it typically dries in just a few minutes.
Is Gekko G70 safe to use?
Yes, the G70 is a low-odour, non chlorinated adhesive that is safe and pleasant to use in any workspace.
How do I clean up the Gekko G70 after use?
The G70 can be easily cleaned up using solvents such as acetone or mineral spirits. It’s important to follow all safety precautions when working with solvents and to dispose of them properly.
Can I reposition the materials once I’ve bonded them with the Gekko G70?
With its fast-drying formula, the G70 makes repositioning bonded materials a challenge. Therefore, it’s advisable to meticulously align the materials before bonding them to secure a proper fit.
How do I store the Gekko G70?
The G70 should be stored in a cool, dry place, away from heat sources and direct sunlight. It’s also essential to keep the can upright and to use the product within its shelf life.
Is the Gekko G70 waterproof?
The G70 is water-resistant but not waterproof. It can withstand exposure to light moisture but may break down under prolonged exposure to water or humidity.
How do I apply the Gekko G70?
The G70 is applied using a spray nozzle. It’s important to hold the can approximately 6-8 inches from the surface to bond and apply the adhesive sweepingly, ensuring even coverage.
Not sure if this spray adhesive is right for you?
If you are not sure if this contact adhesive is right for your individual requirements, please do not hesitate to Contact our friendly sales team and we will be happy to help you.
Do you require a Certificate of Conformance and traceability?
If you require a Certificate of Conformance, please contact us after ordering (either by phone or email) and we will get this sent out to you with your order.
Reviews
There are no reviews yet