TensorGrip F11 is a NON-MECL LOW VOC, high-performance plasticiser resistant adhesive, specially formulated to bond all commonly used substrates found within the foam and upholstery industry. The F11 will bond vinyl, rubber, leathers and plastics, as in the past this was not possible because of the leeching plasticisers migrating from the vinyls causing delamination. F11 is unique due to its capability to bond foams and fabric single-sided when in conjunction with nip rollers
Spray adhesive benefits
When it comes to this contact adhesive it can be used to bond materials on to the following materials.
- 100% resistant to delamination caused by plasticiser migration
- High temperature resistance up to 155C
- Very Good Green Strength
- Fast tack time
- Super smooth web spray
- Will bond many fabrics to difficult substrate
- Very high solids
- Single sided bonding
- Waterproof
Spray adhesive consistancy
The consistancy of this contact adhesive is fine consistant web like spray pattern.
Spray adhesive uses information
When it comes to this contact adhesive it can be used to bond materials on to the following materials.
- Commonly used substrates found within the foam and upholstery industry
- Foam
- Vinyl
- Rubber
- Leathers
- Plastics
Coverage information for this spray glue
This contact adhesive can cover an area up to 80M2.
Save when you buy in bulk
We offer bulk buying options with this sprayable glue. So the more you buy, the more you save.
Contact canister storage and canister change over instructions
Turn valve on canister into the off position, spray out remaining adhesive left in the hose, disconnect the spray hose and gun from the canister.
Reconnect the spray hose to a canister of cleaning solvent (sold separately) and spray out until liquid is clear which indicates that the hose and gun is clean.
If you choose to leave the hose and spray gun on the canister, leave the valve on the canister open. Do not disconnect the hose/gun from the canister.
Close and lock the spray gun.
Handling & Storage Information
- Consult Material Safety Data Sheet prior to use
- DO NOT store at temperatures over 50C
- Avoid exposure to direct sunlight
- DO NOT store directly on a concrete floor
- For optimum performance, store at 18C during use; but, it must always be above 10C
- When connected, keep the valve open and hose pressurised at all times
- DO NOT close the valve until ready to connect to new cylinder
- Release pressure in hose before disconnection
- Always test product to determine suitability for your particular application prior to use in production
How to use this contact spray adhesive
This glue is designed to be applied to two surfaces to be bonded together. Consequently, for best results, the temperature of the adhesive and the surfaces being bonded should be between 60F – 80F (16C – 27C).
Use with adequate ventilation, and when possible we recommend shaking the canister well before using.
Then start spraying. It is as simple as that.
Prior to use, please check compatibility by spraying a small test patch of the adhesive on the substrate, and this glue may degrade some substrates.
Spraying recomendations
- Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc…
- Spray about 10-20 cm (4″ – 8″) away at a 90 degree angle to the surface, applying a uniform, even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another coat of this adhesive in areas that appear to need more adhesive.
- Spray both surfaces to be bonded, one surface vertically and the other surface horizontally
- Allow 2 – 3 minutes for the adhesive to tack off until no adhesive transfers to the knuckle when touched.
- Adhere surfaces and press together with adequate pressure.
- roller is recommended to apply a uniform pressure to achieve maximum strength.
- Allow 24 hours for the adhesive to fully cure.
- If the spray tip clogs, unscrew the spray tip from the gun and clean with solvent such as lacquer thinner or acetone. Do not use a pin on the spray tip orifice
Not sure if this spray adhesive is right for you?
If you are not sure if this contact adhesive is right for your individual requirements please do not hesitate to Contact our friendly sales team and we will be happy to help you.
Do you require a Certificate of Conformance and traceability?
If you require a Certificate of Conformance, please contact us after ordering (either by phone or email) and we will get this sent out to you with your order.
Reviews
There are no reviews yet